Overland Vehicle Outfitters

Project Flatfender: Transmission

Transmission
When it came to a transmission for the project, I considered many different options and finally selected the Muncie SM420. This heavy-duty truck transmission was built by GM and installed in 1/2, 3/4, 1 and 2-ton trucks, busses, and heavy equipment from 1947 to 1967. The SM420 is fully synchronized in second through fourth gears, and all gears are helically cut except first and reverse, which are spur gears. Ratios are as follows: 1st gear = 7.05:1, 2nd gear = 3.6:1, 3rd gear = 1.7:1, 4th gear = 1:1. First is a super-low granny gear that will provide an outstanding crawl ratio for slow speed rocky trails. (My crawl ratio will be 65:1, calculated as 1st gear 7.05 x low-range 2.46 x axle gears 3.73. For more useful 4x4 math, check out my Resources page.) This will allow me to run 3.73 axle gears for fuel economy and highway cruising without giving up my crawling ability. The SM420 will marry directly to the Buick 225 V6 bellhousing, simplifying installation. This is a very compact transmission at only 10.7" in length, perfect for a short wheelbase flattie, although it's no lightweight with its cast iron construction - it weighs in at 135 lbs! Novak Conversions offers an adapter kit to mate the SM420 to the Model 18 transfer-case. After considering all these factors, my transmission choice became pretty clear. I even found a transmission online in very good condition for $200 (gotta' love eBay!).

   

This is the tranny in its original condition. The outside of the case had the expected dirt caked to it, but cleaned up easily. Note the PTO access plate on the near side and the rear yoke that indicates this unit was originally installed in a 2-wheel drive truck. The rear yoke will be removed before installing the transfer-case adapter for the Model 18.

sm420_pre.jpg
sm420_side.jpg

I pulled the top plate to gain access to the internals, then removed the drain plug. With a bucket under the drain hole, I thoroughly cleaned the interior of the case with brake cleaner until it drained clear fluid. I was pleasantly surprised to find the main shaft and gears to be in good condition. The synchros and bearings showed normal wear, so I ordered a rebuild kit to freshen up the small parts and seals while the tranny is out of the vehicle and had ATS Transmission perform the rebuild. After cleaning the outside of the case, I sprayed it with several coats of engine enamel.

The SM420 is a top loaded, top-shifting transmission with the shift mechanism located in the "tower" and top plate. This tranny has a 1 1/8" ten spline input shaft and a ten spline output mainshaft.  A common wear item on this transmission is the two pins in the top of the shift tower which hold the shifter in place.  These were very worn, so Bill (from ATS) removed them and welded in replacements to keep things tight while shifting.

sm420_top.jpg

sm420_fr.jpg

The front bolt pattern is the consistent GM Muncie / Saginaw four-bolt pattern as found on GM bellhousings and transmissions from the 1940's through the 1990's. The bellhousing from the Dauntless 225 V6 will bolt directly to the transmission.

   

(Sidebar:  The 1970 Jeep originally came from the factory with a T-14 3-speed transmission behind the Dauntless V6.  It's interesting to note that this setup included an OEM adapter between the transmission and the bellhousing.  Because the SM-420 bolts directly to the Buick bellhousing, the adapter becomes obsolete.  This saves some crucial inches that are needed for the rear driveshaft in such a short wheelbase vehicle.)

E-mail us at:  rmiller@ovoonline.com

Overland Vehicle Outfitters
Marysville, OH 43040